PERANCANGAN MESIN PENEPUNG DAUN LAMTORO DENGAN MENGGUNAKAN METODE VDI 2222
-
Ronaldo Luis Gama(1*)
Universitas Nusa Cendana
-
Jefri Bale(2)
Program Studi Teknik Mesin, Fakultas Sains dan Teknik Universitas Nusa Cendana
-
Adi Y. Tobe(3)
Program Studi Teknik Mesin, Fakultas Sains dan Teknik Universitas Nusa Cendana
(*) Corresponding Author
Abstract
The method used in this research is the VDI 2222 method. The process of testing the tool is carried out by turning on the motor, and inputting the lamtoro leaves which will be floured into the tube, the results of the design of the lamtoro leaf powder machine with the VDI 2222 method and the results of the lamtoro leaf flour powder machine test, concluded as follows: Design of a lamtoro leaf crushing machine with engine dimensions, namely: Height 50 cm, Width 30 cm and Length 37 cm, and motor power ¼ hp and uses a belt and pulley transmission, by testing the weight of lamtoro leaves, namely 3000 gr (3 kg) with the required time of 420 minutes, then the flouring process is carried out so that it will produce lamtoro flour with a fineness level of 80 mesh. The design stages using the VDI 2222 method are carried out sequentially which can be adjusted to the needs.
Downloads
References
Geramitcioski, T., Mitrevski, V., & Mijakovski, V. (2018, Juli). Desain pers kecil untuk mengekstraksi minyak atsiri menurut VDI 2221. Dalam Seri Konferensi IOP: Ilmu dan Teknik Material (Vol. 393, No. 1, hlm. 012131). Penerbitan TIO.
Pedoman Penulisan Tugas Akhir (Skripsi) Program Sarjana. Kupang: Jurusan Teknik Mesin Undana, 2023.
Pahl, G., Beitz, W. (2010). VDIGuideline2222, Sistematic approach to the development anddesign of technical sistem and products.Verein Deutscher Inginieure. Berlin : Beuth Verlag
Sularso & Kiyokatsu, (2004), "Dasar Perencanaan dan Pemilihan Elemen Mesin", Pradnya Paramita, Polman Bandung, Bandung.
Wiendahl HP. Five years experience with VDI 2222 guideline in a large capital equipment enterprise. Design Studies. 1981 Jul 1;2(3):165-70.
Sutrisna, A., Kamaharudin, S., Panuh, D., & Raharjo, J. (2019). Perancangan Mesin Penghancur Daun Kering Menggunakan Lima Mata Pisau. Journal of Renewable Energy and Mechanics, 2(02), 66-80.
Ningsih, N., Suwati, S., & Ridho, R. (2021). Analisis Performansi Mesin Penepung Kulit Manggis Tipe Vertikal. Protech Biosystems Journal, 1(2), 11-25.
Zamsuri, A., Supratman, M. R., Darmawan, T., Maryanto, R. J., & Avianti, T. (2005). MESIN PENEPUNG BAHAN DASAR PEMBUATAN KUE SERABI BATANG KHAS KABUPATEN BATANG, PEKALONGAN. Pelita-Jurnal Penelitian Mahasiswa UNY, 1(1).
Subagio, D. G. (2011). Rancang Bangun Mesin Tepung Obat Tradisional Dengan Penambahan Blower Penghisap Pada Ruang Giling. Jurnal Teknologi Bahan dan Barang Teknik, 1(1), 1-6.
Copyright (c) 2023 LONTAR Jurnal Teknik Mesin Undana (LJTMU )
This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.
