Pengaruh Variasi Putaran Motor Penggerak Terhadap Optimalisasi Kerja Pada Alat Shaking Table
-
Agustinus Seven Sore(1)
Program Studi Teknik Mesin, Fakultas Sains dan Teknik Universitas Nusa Cendana
-
Jahirwan Ut Jasron(2*)
-
Jack C.A. Pah(3)
Program Studi Teknik Mesin, Fakultas Sains dan Teknik Universitas Nusa Cendana
-
Arifin Sanusi(4)
Program Studi Teknik Mesin, Fakultas Sains dan Teknik Universitas Nusa Cendana
(*) Corresponding Author
Abstract
Indonesia is a country rich in minerals (mining), and iron sand is a source of magnetic material. The tool usually used in iron sand processing is the Shaking Table, a vibrating sieve mechanism that is generated by the force in the rotation of the driving motor for minerals such as metal and sand. This research aims to determine the rotation of the driving motor to obtain good material sieving results. From the test results of 3 kg of iron sand material, the best results were obtained at a rotation of 28.4 Rpm with the result of sieving material in the concentrate category as much as 0.55 kg and in the tailings category as much as 2.45 kg. The greater the pulley ratio, the slower the rotation that occurs on the wheel piston. On the other hand, the smaller the diameter of the pulley, the faster the piston wheel rotates to move the deck-shaking table. This occurs in accordance with the concept of moment of force, the pulley and axle are concentric wheels.
Downloads
References
A. Meinel, “Fine and very fine screening,” Jurnal AT Mineral Processing English Edition, vol. 51, 2010.
C. Sutowo and E. Diniardi, “Perencanaan Mesin Penghancur Plastik Kapasitas 30 kg/jam,” Sintek Jurnal: Jurnal Ilmiah Teknik Mesin, vol. 4, no. 2, 2010.
A. Abbas, A. Triantoro, and R. Riswan, “STUDI PENGOLAHAN MINERAL ZIRCON (ZrO2) MENJADI ZIRCONIA PADA PT KALIMANTAN ZIRCON INDUSTRI DI DESA GOHONG KECAMATAN KAHAYAN HILIR KABUPATEN PULANG PISAU,” Jurnal Himasapta, vol. 5, no. 2, pp. 25–56, 2020.
H. Mujianto and M. Rahmi, “Pengaruh Sudut Kemiringan (Inklinasi) Terhadap Unjuk Kerja Ayakan Getar (Vibrating Screen),” Sigma Teknika, vol. 2, no. 2, pp. 137–142, 2019.
I. Putra, “IDENTIFIKASI KANDUNGAN FE PADA PASIR BESI HASIL PROSES KONSENTRASI MENGGUNAKAN SLUICE BOX,” Jurnal Cahaya Mandalika ISSN 2721-4796 (online), vol. 4, pp. 256–272, 2023.
F. Abdul and H. Wasik, “Analisa Penggunaan Beberapa Jenis Arang Lokal Sebagai Reduktor dalam Proses Pembuatan Besi Spon (Sponge Iron) dari Bahan Baku Pasir Besi Menggunakan Metode Reduksi Langsung,” Jurnal Iptek, vol. 22, no. 2, pp. 43–50, 2018.
S. Aritonang, J. Jupriyanto, and R. Juhana, “Analisis Proses Pengolahan Pasir Besi Menjadi Besi Spons dalam Rangka Mendukung Industri Pertahanan Bahan Baku Baja,” Jurnal Pertahanan dan Bela Negara, vol. 9, no. 1, pp. 1–12, 2019.
Y. Rumbino and N. Banunaek, “Pengaruh Variabel Meja Goyang (Shaking Table) untuk Memisahkan Mineral Mangan dari Mineral Pengotor,” J Teknol, vol. 15, no. 1, pp. 59–62, 2021.
Copyright (c) 2024 LONTAR Jurnal Teknik Mesin Undana
This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.
