Pengaruh Waktu Pemanasan Menggunakan Pemanas Induksi Terhadap Kekerasan dan Struktur Mikro Material S50C
-
Viktor Naubnome(1)
Jurusan Teknik Mesin, Fakultas Teknik, Universitas Singaperbangsa Karawang (UNSIKA)
-
Eri Widianto(2)
Jurusan Teknik Mesin, Fakultas Teknik, Universitas Singaperbangsa Karawang (UNSIKA)
-
Marno Marno(3)
Jurusan Teknik Mesin, Fakultas Teknik, Universitas Singaperbangsa Karawang (UNSIKA)
(*) Corresponding Author
Keywords:
Inducting heater, heat treatment, hardness and microstructure, material S50C
Abstract
Fabrication of inducting heating system for heating treatment in S50C materials have been done. This inducting heating system has dimensions of 350x230x200 mm, the input voltage of 12 VDC, equipped with a timer control and ampere meter as an indicator of output current. Inducting heating system testing on the material S50C was done by varying tempering process (30, 60, 90, 120 and 150 s). Hardness and microstructure test using Auto Vikers Future Tech type FV-300. The results showed that the hardness increased with increasing tempering time from 191 Hv to 572 Hv. S50C materials microstructure was transformed from ferrite and pearlite phase into martensite phase.
Downloads
Download data is not yet available.
References
[1] Smallman, R.E. dan Bishop, R.J., 2000, Metalurgi Fisik Modern & Rekayasa Material, Erlangga, Jakarta.
[2] ASM Handbook Committee, 1985, Metals Handbook, Volume 9 Edisi 9, Metallography and Microstructures, American Society for Metals International, New York.
[3] ASM Handbook Comitte, 1986, Metal Handbook, Volume 6 Edisi 8, Welding, Brazing and Soldering, American Society for Metals International, New York.
[4] ASM Handbook Committee, 1991, Metals Handbook, Volume 4, Heat Treating, American Society for Metals International, New York.
[5] Krauss G., 2006, Steel Processing, Structure, and Performance, Ohio
[6] Bala, P., Pacyna, J., and Krawczyk, J., 2007. The kinetics of phase transformations during tempering of low alloy medium carbon steel, International Scientific Journal of the Committee of Materials Science of the Polish Academy of Sciences vol. 28, no. 2. Feb. 2007. pp. 98-104.
[7] S. Mizhar dan Suherman, 2011, Pengaruh perbedaan kondisi tempering terhadap struktur mikro dan kekerasan dari baja AISI 4140, Jurnal Dinamis, Vol. II No.8, ISSN 0216-7492
[8] V. Rudnev, D. Loveless, R. Cook dan M. Black, 2003, Handbook of Induction Heating, Marcel Dekker Inc., USA.
[9] E. Bowyer, 1987, Practical Heat Treating, American Society for Metal (ASM), Ohio, US.
[10] R. Ismail, M. Tauviqirrahman, Jamari dan D.J. Schipper, 2009, Finite Element Analysis of Sliding Contact of a Hard Cylinder on a Layered Elastic-Plastic Solid, Proceedings of International Conference on Advances Mechanical Engineering (ICAME), Shah Alam, Malaysia.
[11] R. Ismail, M. Tauviqirrahman, Jamari dan D.J. Schipper, 2009, The Finite Element Study of Static Contact on Multilayered Solids, The 6th International Conference on Numerical Analysis in Engineering, Mataram, Nusa Tenggara Barat, Indonesia.
[12] Jamari, R. Ismail dan M. Tauviqirrahman, 2011, Modeling of Surface Hardening Layer on Transmission Gear, International Conference and Exhibition on Sustainable Energy and Advanced Materials (ICE SEAM 2011) Solo-Indonesia.
[13] R. Ismail, Jamari, M. Tauviqirrahman, Sugiyanto dan T. Andromeda, 2011, Surface Hardening Characterization of
Transmission Gears, Prosiding Seminar Nasional Sains dan Teknologi 2, Universitas Wahid Hasyim, Semarang.
[14] R. Ismail, M. Tauviqirrahman, A.P. Bayuseno, Sugiyanto dan Jamari, 2013, Pemanfaatan Alat Pemanas Induksi untuk Industri Kecil dan Menengah, Prosiding Seminar Nasional Mesin dan Teknologi
Kejuruan, Universitas Negeri Jakarta, Jakarta.
[15] R. Ismail, D. I. Prasetyo, M. Tauviqirrahman, E. Yohana dan A.P. Bayuseno, 2014, Induction Hardening of Carbon Steel Material: The Effect of Specimen Diameter, International Conference on Key of Engineering (ICKEM), Accepted
[2] ASM Handbook Committee, 1985, Metals Handbook, Volume 9 Edisi 9, Metallography and Microstructures, American Society for Metals International, New York.
[3] ASM Handbook Comitte, 1986, Metal Handbook, Volume 6 Edisi 8, Welding, Brazing and Soldering, American Society for Metals International, New York.
[4] ASM Handbook Committee, 1991, Metals Handbook, Volume 4, Heat Treating, American Society for Metals International, New York.
[5] Krauss G., 2006, Steel Processing, Structure, and Performance, Ohio
[6] Bala, P., Pacyna, J., and Krawczyk, J., 2007. The kinetics of phase transformations during tempering of low alloy medium carbon steel, International Scientific Journal of the Committee of Materials Science of the Polish Academy of Sciences vol. 28, no. 2. Feb. 2007. pp. 98-104.
[7] S. Mizhar dan Suherman, 2011, Pengaruh perbedaan kondisi tempering terhadap struktur mikro dan kekerasan dari baja AISI 4140, Jurnal Dinamis, Vol. II No.8, ISSN 0216-7492
[8] V. Rudnev, D. Loveless, R. Cook dan M. Black, 2003, Handbook of Induction Heating, Marcel Dekker Inc., USA.
[9] E. Bowyer, 1987, Practical Heat Treating, American Society for Metal (ASM), Ohio, US.
[10] R. Ismail, M. Tauviqirrahman, Jamari dan D.J. Schipper, 2009, Finite Element Analysis of Sliding Contact of a Hard Cylinder on a Layered Elastic-Plastic Solid, Proceedings of International Conference on Advances Mechanical Engineering (ICAME), Shah Alam, Malaysia.
[11] R. Ismail, M. Tauviqirrahman, Jamari dan D.J. Schipper, 2009, The Finite Element Study of Static Contact on Multilayered Solids, The 6th International Conference on Numerical Analysis in Engineering, Mataram, Nusa Tenggara Barat, Indonesia.
[12] Jamari, R. Ismail dan M. Tauviqirrahman, 2011, Modeling of Surface Hardening Layer on Transmission Gear, International Conference and Exhibition on Sustainable Energy and Advanced Materials (ICE SEAM 2011) Solo-Indonesia.
[13] R. Ismail, Jamari, M. Tauviqirrahman, Sugiyanto dan T. Andromeda, 2011, Surface Hardening Characterization of
Transmission Gears, Prosiding Seminar Nasional Sains dan Teknologi 2, Universitas Wahid Hasyim, Semarang.
[14] R. Ismail, M. Tauviqirrahman, A.P. Bayuseno, Sugiyanto dan Jamari, 2013, Pemanfaatan Alat Pemanas Induksi untuk Industri Kecil dan Menengah, Prosiding Seminar Nasional Mesin dan Teknologi
Kejuruan, Universitas Negeri Jakarta, Jakarta.
[15] R. Ismail, D. I. Prasetyo, M. Tauviqirrahman, E. Yohana dan A.P. Bayuseno, 2014, Induction Hardening of Carbon Steel Material: The Effect of Specimen Diameter, International Conference on Key of Engineering (ICKEM), Accepted
Published
2014-04-01
How to Cite
Naubnome, V., Widianto, E., & Marno, M. (2014). Pengaruh Waktu Pemanasan Menggunakan Pemanas Induksi Terhadap Kekerasan dan Struktur Mikro Material S50C. LONTAR Jurnal Teknik Mesin Undana, 4(1), 48-52. https://doi.org/10.35508/ljtmu.v4i1.1621
Section
Articles
