Analisis Kinerja Pompa Regeneratif Tunggal dan Paralel
-
Aldian Ndoen(1)
Program Studi Teknik Mesin, Fakultas Sains dan Teknik Universitas Nusa Cendana
-
Matheus M. Dwinanto(2*)
Program Studi Teknik Mesin, Fakultas Sains dan Teknik Universitas Nusa Cendana
-
Ishak s Limbong(3)
Program Studi Teknik Mesin, Fakultas Sains dan Teknik Universitas Nusa Cendana
(*) Corresponding Author
Abstrak
One important aspect of fluid machines engineering that is related to the use of electrical energy to achieve useful functions and has been widely used in industry and households is the regenerative pump. This pump can produce a high head with a relatively small discharge. This experimental study aims to analyze the effect of discharge variations on the performance of single and parallel regenerative pumps. Tests were carried out on two regenerative pumps with the same specifications at varying discharges, starting from the minimum flow to the maximum that can be achieved by the pump. The test results show that the construction of the piping system greatly influences the performance of the regenerative pump which is operated as a single pump whereas the flow rate increases, the total head, hydraulic power and pump efficiency will tend to decrease, and vice versa. The pump shaft power tends to remain constant even though the flow rate increases. In parallel operation, an increase in flow rate will result in a decrease in total head, hydraulic power, shaft power and pump efficiency, and vice versa. Increasing the flow rate to double will result in different total head, hydraulic power, shaft power and pump efficiency for each pump
##plugins.generic.usageStats.downloads##
Referensi
[2]. Choi, W. C., Yoo, I. S., Park, M. R. and Chung, M. K. 2013. Experimental study on the effect of blade angle on regenerative pump performance, Journal of Power and Energy, 227 (5): 585 – 592.
[3]. Engeda, A. 2003. Flow analysis and design suggestions for regenerative flow pumps. Proceedings of ASME FEDSM’03 4th ASME_JSME Joint Fluid Engineering Conference. 1 – 11. Honolulu, Hawai, USA, July 6 – 10.
[4]. Meakhail, T. and Park, S. O. 2005. An improved theory for regenerative pump performance. Proceedings of IMechE Vol. 219 Part A: J. Power and Energy. 213 – 222.
[5]. Quail, F., Scanlon, T. and Stickland, M. 2011. Design optimisation of a regenerative pump using numerical and experimental techniques. International Journal of Numerical Methods for Heat and Fluid Flow, 21(10): 95 – 111.
[6]. Karanth, K. V., Manjunath, M. S., Kumar, S. and Sharma, N. Y. 2015. Numerical Study of a Self-Priming Regenerative Pump for Improved Performance using Geometric Modifications, International Journal of Current Engineering and Technology, 5(1): 104 – 109.
[7]. Nejadrajabali, J., Riasi, A., and Nourbakhsh, S. A. 2016. Flow Pattern Analysis and Performance Improvement of Regenerative Flow Pump Using Blade Geometry Modification, International Journal of Rotating Machinery, 2016: 1 – 16.
[8]. Jeon, S-Y., Kim, C-K., Lee, S-M., Yoon, J-Y and Jang, C-M. 2017. Performance Enhancement of a Pump Impeller Using Optimal Design Method. Journal of Thermal Science, 26(2): 119 – 124.
[9]. Wahyudi, D. dan Haryono, S. 2011. Uji Kinerja Pompa Sentrifugal Susunan Paralel terhadap Head dan Kapasitas, Energy (Jurnal Ilmiah Ilmu-Ilmu Teknik), 1(1): 57 – 63.
[10]. Febrianto, I., Kabib, M. dan Nugraha, B. S. 2018. Perancangan Sistem Pompa Paralel Dengan Daya Bervariasi Untuk Meningkatkan Kapasitas Air, Jurnal CRANKSHAFT, 1(1): 49 – 54.
[11]. Syahrizal, I. dan Perdana, D. 2019. Kajian eksperimen instalasi pompa seri dan paralel terhadap efisiensi penggunaan energi, Jurnal TURBO, 8(2): 194 – 200.
[12]. Pritchard, P. J., and Leylegian, J. C. 2011. Introduction to Fluid Mechanics (Fox and McDonald’s), Eighth Edition, John Wiley & Sons, Inc. pp. 516 – 518.
